絲印PP油墨 

歐萊斯絲印PP油墨

主要用于PP、PE、BOPP等材料上，具有高色澤、高色彩、高遮蓋力、高穩定性、耐酒精及耐磨擦之特點。 
印刷：絲印移印均可。 
表干及實干時間：表干時間自然揮發5-10分鐘；實干時間在24小時以內。 
稀釋及清洗：SV3慢干開油水、UVK1（移印開油水）同時可使用718洗網水清洗。 
 
測試方法（完全干燥后）： 
1、3m膠紙粘在畫有百格的油墨表面，45度角迅速拉起不脫油； 
2、純度99%的工業酒精，一千克砝碼用棉布包住在油墨表面，以水平力來回拉200次無脫色； 
3、耐磨：橡皮擦500g力水平來回擦500次。 
 
使用方法： 
1、使用前應充分?jǐn)嚢�，用后隨時封閉； 
2、攪拌時加開油水10-15%，稀釋到印刷粘度； 
3、網板塞網時可用洗網水清洗； 
4、不得與其它類型油墨混合使用。 
 
注意事項： 
1、塑膠材料的外觀相似，但可能會是不同的材料，客戶需試印確定其符合要求后，再批量印刷； 
2、在移印過程中，如出現拉絲或散開，可適當加入一些慢干膏即可； 
3、環境溫度過高，將會影響油墨原有質量； 
4、根據氣候變化，請遠離火源，陰暗環境下存放。
    5、技術參考數見下表：
       檢驗項目 檢驗結果 測試條件 
       油墨線度 ≤12um 刮板細度計 
       干膜光澤 ≥65° 60°鏡面光澤計 
       干燥速度 表干 25℃×5-10min 或60℃×2-3min 
       實干 25℃12Hr或60℃×10min 
       耐酒精性 無變化 500克力/cm2酒精棉200次來回 
       附著力 100/100 1mm×1mm×100格3M膠紙剝離 
       耐酸性 無變化 浸泡5%HCI×24Hr 
       耐堿性 無變化 浸泡5%NaOH×24Hr 
       耐鹽性 無變化 浸泡5%NaCI×24Hr  
       耐水性 無變化 浸泡20℃自來水×96Hr   
       耐磨性 不見底 500克/cm2負載含砂橡皮200來回 
       耐熱性 無變化 80℃×12Hr  

 Ink characteristics: have and Germany Caili treasure the same color, is mainly used for PP, PE, BOPP and other materials, with a high color, high color, high covering power, alcohol resistant and wear resistance, high stability.
Printing: silk screen printing can be.
Table dry and work time: surface dry time natural volatile 5-10 minutes; work time within 24 hours.
Dilution and cleaning: SV3 slow dry open water, UVK1(printing open water) also can use 718 washing network water cleaning.
Test method (completely dry):
1, 3M adhesive tape sticky ink surface adhesion in painting,45 degree angle quickly pulled off the oil;
2, purity 99% of industrial alcohol, using cotton bag in the surface of the ink one kilogram weight to horizontal force and pull 200 times without decolorization;
3, wear: the eraser 500g force level wipe 500 times back and forth.
Method of use:
1, before the use should be fully mixing, use at any time after the closure;
2, mixing an additional 10-15% in oil and water, diluted to printing viscosity;
3, mesh plug mesh can be used when washing network water cleaning;
4, shall not be mixed with other types of ink.
The matters needing attention:
1, the plastic material of similar appearance, but may be of different materials, customers need to try to determine its requirements, and then bulk printing;
2, in the printing process, such as drawing or spread out,may be appropriate to add some slow dry paste can be;
3, the ambient temperature is too high, it will affect the quality of the original ink;
4, according to the climate change, please stay away from fire, stored in dark environment.